The coin minting process is the sequence of steps and tools that national mints use to turn sheets of metal into finished coins. It begins with metal strip, which is cut into blanks, softened, cleaned and given a raised rim. The prepared discs are then struck between two engraved steel dies inside a ring called a collar, in a high-speed press.
The same basic method is used by national mints worldwide, whether they make low-value circulating coins, bullion coins or proofs for collectors. Each tool in the chain affects the finished coin: the quality of the hub and dies controls the sharpness of the design, the collar shapes the edge, and the press force decides how fully the metal fills the design. Faults at any stage create error coins. The physical features produced, such as the rim, field and edge, are described on the page Parts of a Coin.
Planchet
A planchet is the metal disc on which a coin is struck. Before it has its rim raised it is usually called a blank, and the two words are often used loosely for each other. Blanks are punched out of coils or sheets of metal rolled to the exact thickness for the coin, using a blanking press that can cut many discs with each stroke. The metal is chosen for the coin's design; see Coin Metals and Alloys.
Punching hardens the metal, so blanks are annealed: heated in a furnace to soften them so that they take the design cleanly and do not crack in the press. They are then washed and dried to remove oxidation and leave a bright surface, and passed through the upsetting mill. Planchets with the wrong thickness, alloy or shape, or with clipped or cracked edges, lead to striking and planchet errors.
Upsetting Mill
An upsetting mill is the machine that squeezes the edge of a blank to raise a rim before the blank is struck. Blanks are rolled through a groove between a rotating wheel and a fixed track that narrows slightly, which pushes metal inward and upward around the edge. The result is a disc with a thicker raised border and a slightly smaller diameter, ready to fit inside the collar of the press.
The step is what turns a blank into a planchet in most minting terminology. The raised rim protects the design of the finished coin from wear, helps coins stack neatly and makes it easier for the metal to flow into the border of the dies when the coin is struck. If a blank skips the upsetting mill, the coin can come out with a weak or missing rim, a fault collectors note among planchet errors.
Hub
In coin making, a hub is a hardened steel punch carrying the coin's design in relief, raised as on the finished coin, and used to sink the design into dies. It has nothing to do with payment hubs or trading hubs. Mints make dies in a chain: an original model produces a master hub, the master hub is pressed into steel to make a master die, the master die makes working hubs, and each working hub is pressed into softened steel blanks to make many working dies.
The chain allows a mint to produce thousands of identical dies from one design, which keeps every coin of a type the same and makes copies harder for counterfeiters to match. Older methods needed several impressions of the hub into each die, and any shift between them could produce a doubled die. Modern single-press hubbing has largely reduced such errors; see Die-Related Coin Errors.
Die
A die is a hardened steel cylinder whose face carries the coin design in reverse, sunk into its surface. Two dies strike each coin: the obverse die for the front, normally the portrait or national emblem, and the reverse die for the back. In modern presses one die is fixed and the other moves; in hand striking these were called the anvil die, set in a block, and the hammer die, struck from above.
Working dies are made from hubs, hardened by heat treatment and sometimes plated or polished, especially for proof coins. Each die wears with use, and its life is measured in the number of coins it strikes before the design loses sharpness or the steel cracks. Mints track die use as part of quality control and record keeping; see Coin Production Methods and Records.
Collar
A collar is the steel ring that surrounds the lower die in a coining press, holding the planchet in place and forming the coin's edge as metal expands against it during striking. A close collar, also called a closed collar, fits tightly so that each coin has a uniform diameter and a perfectly round edge. A plain collar gives a smooth edge; a reeded collar has grooves that give the familiar milled edge on many coins. The term is unrelated to collars in options trading.
Older open collars only loosely positioned the blank, so coins varied in size. Segmented collars, made of sections that open after striking, allow lettering or patterns in relief on the edge. Reeded and lettered edges were first used to defeat clipping, the shaving of precious metal from coin edges, and remain a security feature against counterfeiting.
Coining Press
A coining press is the machine that strikes a planchet between the two dies with enough force to make the metal flow into every part of the design. For most of history coins were struck by hand, with a hammer on a pair of dies. Screw presses, turned by men or animals, were adopted in Europe from the sixteenth century, and England replaced hammered coinage with machine-struck milled coinage in the 1660s.
In the late eighteenth century, the engineer Matthew Boulton applied steam power to coining at his Soho works in Birmingham, and steam presses soon spread to national mints. Modern presses are hydraulic or mechanical machines that feed planchets automatically and can strike several hundred coins a minute for circulation. Proof and commemorative coins are struck more slowly, often more than once, on polished planchets. In the United States the work is spread across several plants; see United States Mint Facilities.
From strip to finished coin
The stages follow one order. Metal strip is blanked into discs; the blanks are annealed, cleaned and upset into planchets; dies are made from hubs; and the planchets are struck in a press with a collar. The finished coins are then inspected, counted and bagged for delivery to the central bank or treasury that issues them. Coins made for collectors may also be graded after sale; see Coin Grading.
Ref 1150000108