DeFi lending risk parameters are the numbers a pool-based lending protocol sets for each asset to keep loans over-collateralised and the pool solvent. Protocols such as Aave and Compound have no credit checks: every loan is backed by deposited collateral, and these settings decide how much can be borrowed against it, when a position can be liquidated, how large the pool may grow and what interest borrowers pay.
The parameters are chosen by protocol governance, usually token holders in a decentralized autonomous organization (DAO) acting on advice from specialist risk teams, and they differ by asset according to its liquidity and price volatility. They work together: the liquidation threshold feeds the health factor, caps limit how much any one asset can affect the lending pool, and the utilization rate and reserve factor set the interest paid and earned. Special borrowing modes that adjust these numbers are covered in DeFi lending modes and credit delegation.
Health Factor
The health factor is a single number that shows how safe a borrowing position is. It compares the borrower's risk-weighted collateral with its debt:
Here is the market value of each collateral asset, is the liquidation threshold of that asset written as a decimal, and is the value of all debt, all measured in the same currency using prices supplied by an oracle. While the health factor is above 1 the position is safe; once it falls below 1 the position can be liquidated.
For example, a borrower supplies collateral worth $10,000 with a liquidation threshold of 80 percent and borrows $6,000. The health factor is . If the collateral falls to $7,000, the health factor becomes , and the loan can be liquidated. The break-even collateral value is dollars.
Liquidation Threshold
The liquidation threshold is the percentage of a collateral asset's value at which a loan becomes eligible for liquidation. It is set a little above the maximum loan-to-value ratio (LTV), which is the most a borrower may draw when opening or increasing a loan. The gap between the two is a safety buffer: a new loan never starts at the edge of liquidation.
Suppose an asset has a maximum LTV of 75 percent and a liquidation threshold of 80 percent. Against $10,000 of that asset, a borrower can take up to $7,500. The loan becomes liquidatable when the debt exceeds 80 percent of the collateral value, either because the collateral price falls or because interest builds up the debt. Volatile or thinly traded assets get lower thresholds, and some assets have a threshold of zero, meaning they cannot be used as collateral at all.
Liquidation Bonus
The liquidation bonus is the extra collateral a liquidator receives for repaying part of an unhealthy loan. Seen from the borrower's side, the same amount is often called the liquidation penalty. The bonus pays outside bots and traders to watch positions and act quickly, so the protocol does not need its own liquidation desk. The collateral a liquidator can claim is:
where is the value of collateral seized, is the debt repaid and is the bonus as a decimal. With a 5 percent bonus, a liquidator who repays $3,000 of debt receives collateral worth dollars. Bonuses typically range from about 5 to 10 percent, higher for riskier assets. A protocol may cap how much of a loan can be repaid in one liquidation.
Supply Cap
A supply cap is a governance-set maximum on the total amount of an asset that can be deposited into a lending pool. Once deposits reach the cap, further supply transactions fail until the cap is raised or funds are withdrawn. It is not the same as a token's maximum supply, which limits how many units of the token can ever exist.
The cap limits concentration risk. If a large share of a thinly traded token were deposited as collateral, a price drop could trigger liquidations that the market could not absorb, leaving bad debt in the pool. A cap also limits the damage from oracle manipulation: an attacker who pushes up the token's price can borrow only against the capped amount. Caps are usually raised in steps as an asset's market deepens.
Borrow Cap
A borrow cap is a governance-set maximum on the total amount of an asset that can be borrowed from a lending pool, across all users. When total borrowing reaches the cap, new loans of that asset are refused, although existing loans continue to accrue interest.
Borrow caps limit the pool's exposure to assets that are hard to source in a crisis or are easy to borrow and dump. They also reduce the scope for attacks that borrow a large amount of a thin token in order to move its price elsewhere, sometimes funded with a flash loan. Borrow caps are paired with supply caps: the supply cap limits how much of an asset can act as collateral, and the borrow cap limits how much of it can be owed. A cap of zero switches borrowing of an asset off entirely.
Reserve Factor
The reserve factor is the share of the interest paid by borrowers that a lending protocol keeps for its own reserves or treasury instead of passing it to suppliers. It is set per asset by governance, and the reserves can be used to cover bad debt, fund development or act as a buffer for depositors. The supply rate depends on it:
where is the supply rate, is the borrow rate, is the utilization rate and is the reserve factor. With a borrow rate of 5 percent, utilization of 80 percent and a reserve factor of 10 percent, suppliers earn , or 3.6 percent. The remaining 0.4 percent of supplied funds per year goes to the reserve. Suppliers usually receive their share through interest-bearing tokens whose balance or value grows over time.
Utilization Rate
The utilization rate is the share of an asset's supplied liquidity that is currently lent out:
where is total borrowing of the asset and is the total supplied. A pool with 1,000,000 units supplied and 900,000 borrowed has a utilization rate of 90 percent. Most protocols set the borrow rate from utilization with a kinked curve: rates rise gently up to an optimal utilization , then steeply above it, to attract new supply and push borrowers to repay before the pool runs dry. Below the kink:
and above it:
with base rate and slopes and . With , , and , utilization of 40 percent gives , while 90 percent gives . This is different from the utilization rate in securities lending, which measures how much of a lendable stock is on loan.
How the parameters fit together
| Parameter | What it limits | Who it mainly affects |
|---|---|---|
| Health factor | Whether a position can be liquidated | Borrowers |
| Liquidation threshold | Collateral value counted for safety | Borrowers |
| Liquidation bonus | Reward for repaying unhealthy debt | Liquidators and borrowers |
| Supply cap | Total deposits of an asset | Suppliers and the pool |
| Borrow cap | Total borrowing of an asset | Borrowers and the pool |
| Reserve factor | Share of interest kept by the protocol | Suppliers and the treasury |
| Utilization rate | Not a limit: drives interest rates | Everyone in the pool |
Badly set parameters are a common cause of losses. Thresholds that are too high or bonuses that are too low can leave positions under water before liquidators act, and sharp market falls can set off cascading liquidations that push prices down further.
Ref 1070001392