Capacity utilization is the proportion of productive capacity that is actually being used. It compares what factories, mines and utilities are producing with the most they could produce on a sustained basis using their existing plant and equipment. A rate of 78 percent means that output is running at 78 percent of that sustainable maximum. The measure can be calculated for a single plant, a company, an industry or a whole economy.
Economists and investors use the rate as an indicator of slack. A low rate signals idle resources and weak demand. A high rate signals that producers are stretched, which may lead to rising prices and to new investment. In the United States the standard figures are published each month by the Federal Reserve, and other countries compile similar data, often from business surveys.
Formula and example
The rate is:
- Actual output is the volume produced in the period, measured for industries by an index of production.
- Potential output, or capacity, is the greatest level of output that could be maintained under a realistic work schedule, allowing for normal downtime and with enough labour and materials available.
A plant able to produce 1,000 units a month that turns out 820 units is operating at percent. If demand weakens and it produces 700, the rate falls to 70 percent. Fixed costs are then spread over fewer units, so the cost of each unit rises and profit margins shrink, which is why the rate matters to company earnings as well as to economists.
Capacity in this sense is not an engineering maximum. A factory could run around the clock for a short time, but the measure refers to a level that can be kept up. Full use in practice is therefore well below 100 percent.
The Federal Reserve measure
The Federal Reserve Board publishes capacity utilization together with its index of industrial production in a statistical release known as G.17, issued around the middle of each month for the month before. It covers manufacturing, mining, and electric and gas utilities, which together make up the industrial sector. Services, construction and agriculture are not included, so the measure describes a minority of the modern economy, though a part that swings widely over the business cycle.
The production indexes are built from data on physical output, hours worked and electricity use. Capacity is estimated from surveys of plant capacity, physical capacity data from trade sources and estimates of the stock of capital goods. Both are revised, and capacity estimates in particular are less certain than output. The long-run average for total industry since the early 1970s is close to 80 percent. The rate has fallen into the 60s in deep downturns, as in the recession of 2008 to 2009 and the shutdowns of early 2020, and has reached the high 80s at peaks.
Link with inflation and investment
When utilization is high, firms have little spare capacity to meet extra orders. They may pay overtime, bring older and less efficient equipment back into use and face delays from suppliers, all of which raise costs and make price increases easier to pass on. High utilization has therefore been treated as an early sign of inflation, and a rate in the low to mid 80s was long regarded in the United States as the zone where such pressure builds. The idea is an industrial counterpart of the output gap for the whole economy and is related to the concept of the NAIRU in the labour market.
The relationship has weakened over time. Manufacturing is a smaller share of output than it was, and goods prices are strongly affected by imports, so domestic capacity is a less binding limit. The surge in prices in 2021 and 2022 owed more to disrupted supply chains than to a high measured rate.
The rate also guides investment. Companies operating near capacity have a reason to build new plant and buy equipment, so a rising rate tends to come before higher capital expenditure. Persistently low rates point the other way and can signal overcapacity in an industry, a recurring concern in sectors such as steel, where surplus capacity in one country depresses prices worldwide.
How markets read the release
The monthly figure is compared with economists' forecasts, though it attracts less attention than data on jobs or consumer prices. A stronger reading supports the view that gross domestic product is growing and may raise expectations of tighter monetary policy. A falling rate alongside declining production is one of the signals of contraction in manufacturing. Analysts of cyclical industries, including chemicals, paper, metals and semiconductors, follow industry-level rates closely, since pricing power in those sectors tends to appear only when utilization is high.
Limitations
Capacity is an estimate, not an observed quantity. Plants differ in age and efficiency, and capacity that exists on paper may be uneconomic to operate. Structural change can leave obsolete capacity in the figures, which understates how tight conditions really are. The measure says nothing about services, where capacity is hard to define, and gains in productivity can raise potential output without any new plant. For a view of the whole economy, analysts combine it with measures of labour market slack and estimates of aggregate supply.